Request Info

SPECS SUMMARY

Flywheel Power - Tractor/Scraper425 kW (570 hp)/216 kW (290 hp)
Scraper Capacity - Heaped50 yd³ (38 m³)
Top Speed - Loaded34.7 mile/h (55.8 km/h)
Rear Axle - Rear of Machine95.4 in (2424 mm)
637K coal bowls are longer and higher than standard wheel tractor scraper bowls, allowing them to haul 38 m (50 yd) of low density loose coal. The bowls are designed and built to specifically deliver in coming loose coal to the stock pile and reserve stock piled coal to the feeder system.

Specifications

Flywheel Power - Tractor/Scraper425 kW (570 hp)/216 kW (290 hp)
Scraper Capacity - Heaped50 yd³ (38 m³)
Top Speed - Loaded34.7 mile/h (55.8 km/h)
Rear Axle - Rear of Machine95.4 in (2424 mm)
Flywheel Power - Scraper290 HP (216 kW)
Maximum Depth of Spread21.1 in (535 mm)
Transmission Gear - Sixth19 mile/h (30.6 km/h)
Bail Lower2.1 s (2.1 s)
EmissionsCat C9.3 and Cat C18 engines meet U.S. EPA Tier 4 Final/EU Stage IV engine emission standards.
Maximum Depth of Cut17.7 in (450 mm)
Height - Scraper Blade Maximum21.2 in (538 mm)
Scraper Capacity - Struck41 yd³ (31 m³)
Apron Raise4 s (4 s)
Transmission Gear - Fifth14.1 mile/h (22.7 km/h)
Transmission Gear - Seventh25.7 mile/h (41.95 km/h)
Hydraulic System37.5 gal (US) (142 l)
Overall Shipping Height13.62 ft (4.15 m)
Ejector Retract8.5 s (8.5 s)
Width - Outside Rear Tires143.2 in (3636 mm)
Rated Load34 472 kg (76,000 lb)/34.20 tonnes (38 tons)
Cooling System - Tractor19.8 gal (US) (75 l)
Width - Inside of Bowl134 in (3404 mm)
Height - Overall Shipping163 in (4140 mm)
Rollover Protection Structure (ROPS)ISO 3471:2008 for up to 21 282 kg (46,919 lb)
Length - Overall Machine - Standard609.5 in (15480 mm)
Exterior Sound Power LevelThe exterior sound power level for the standard machine (ISO 6393:2008) is 118 dB(A).
Bowl Raise3.5 s (3.5 s)
Ejector Extend8.5 s (8.5 s)
Crankcase - Scraper6.5 gal (US) (24.5 l)
Width - Rear Tire Centers96.9 in (2462 mm)
Reverse AlarmISO 9533:2010
Transmission Gear - Second6.2 mile/h (10 km/h)
Tires - Scraper37.25R35**E3
Engine Model - TractorCat C18
Engine Model - ScraperCat C9.3
Front of Tractor to Front Axle142.2 in (3612 mm)
Fuel Tank Refill Capacity - Scraper370 gal (US) (1400 l)
ROPS/FOPSMeet ISO standards
Transmission System - Scraper12.9 gal (US) (49 l)
Width - Overall Machine155 in (3937 mm)
Crankcase - Tractor13.7 gal (US) (52 l)
Width - Tractor137.8 in (3499 mm)
Transmission System - Tractor29 gal (US) (110 l)
Tires - Tractor37.25R35**E3
Transmission Gear - First3.4 mile/h (5.5 km/h)
Diesel Exhaust Fluid - Scraper5.8 gal (US) (22 l)
Bail Raise1.5 s (1.5 s)
Bowl Lower3.5 s (3.5 s)
Flywheel Power - Tractor570 HP (425 kW)
Transmission Gear - Eighth34.7 mile/h (55.8 km/h)
Cooling System - Scraper16.1 gal (US) (61 l)
180° Curb-to-Curb Turning Width42.59 ft (12.98 m)
Steering SystemISO 5010:2007
BrakesISO 3450:2011
Ground Clearance - Tractor26.1 in (664 mm)
Diesel Exhaust Fluid - Tractor8 gal (US) (30.5 l)
Transmission Gear - Third7.7 mile/h (12.4 km/h)
Operating Weight - Empty117782 lb (52425 kg)
Overall Length609.5 in (15480 mm)
Top Speed - Loaded34.7 mile/h (55.8 km/h)
Transmission Gear - Reverse6.2 mile/h (9.9 km/h)
Width - Cut11.5 ft (3.51 m)
Scraper Capacity - Heaped50 yd³ (38 m³)
Transmission Gear - Fourth10.5 mile/h (16.9 km/h)
Rated Engine RPM - Tractor1900 r/min (1900 r/min)
Apron Lower3.8 s (3.8 s)
Fuel Tank370 gal (US) (1400 l)
Height - Top of Cab147 in (3733 mm)
Falling Object Protective Structure (FOPS)ISO 3449:2005 Level II
Seat BeltSAE J386:FEB2006
Axle to Vertical Hitch Pin20 in (509 mm)
Rated Engine RPM - Scraper2150 r/min (2150 r/min)
Overall Width12.93 ft (3.94 m)
Wheel Base377 in (9576 mm)

Benefits and Features

  • Coal Bowls are longer and higher than standard scraper bowls, which allows Wheel Tractor-Scrapers to haul 38 m (50 yd) of low density loose coal. The bowls are designed and built to specifically deliver in coming loose coal to the stock pile and reserve stock piled coal to the feeder system.
  • Sequence Assist (optional) uses cylinder position sensors to automate bowl, apron and further implement controls throughout the four core work cycles: Dig, Haul, Unload and Return. When utilized this can reduce up to 14 individual operator commands per cycle. Sequence Assist simplifies control over the implements, reduces joystick usage, automatically controls cushion hitch, transmission hold and ejector.

  • The fuel, water and engine oil are relocated at ground level on the right hand side of the machine for easy access.
  • In cold weather conditions the machine will use the Auto Stall feature to help warm up the transmission oil faster resulting in the machine shifting out of torque converter drive (2nd gear) faster than on previous models.

  • Brakes have been changed from an air actuated drum shoe brake to a hydraulic actuated tractor wet disc brake and a scraper dry caliper.
  • Tire Spin Reduction allows the machine to control the slip of the tractor tires only. When Tire Spin Reduction is selected the machine will control wheel spin on the tractor by keeping the slip in the optimal range for loading by adjusting engine rpms with no additional operator input.
  • Engine Over Speed Protection - In the event of an engine over speed situation, the compression brake or brakes will automatically engage with no operator input. The machine determines the over speed condition based on rate of acceleration and applies compression brakes automatically.
  • Differential Lock Engagement Protection allows the machine to prevent the operator from engaging the differential lock when damage could occur.
  • Coal bowl scrapers are effective in compacting coal, which reduces the risk of spontaneous combustion of coal in the stockpile by eliminating the air spaces.

  • Advanced Cushion Hitch allows the cushion hitch to prevent end stroke by having the ability to predict end stroke events and manage the rate of dampening. Resulting in reduced hitch maintenance and improved operator ride in rough conditions.
  • The K Series steering system design requires significantly less steering effort. The reduced steering effort will allow for decreased operator fatigue and a more efficient operator resulting in possible higher rates of production late in the work cycle.
  • The K Series cab interior improves operator comfort and visibility. The overall interior is 21% larger than the G Series cab.

  • Machine Speed Limitis designed to take the place of top gear selection. If the machine top speed needs to be limited the operator can select the top speed through the display or the top speed can be set in ET. This will allow the machine to find the correct gear that works best for the engine and transmission. Allowing the engine and transmission to select the correct gear to pull the load in most cases resulting in a lower engine load factor and lower fuel burn verses using top gear selection that required the machine to run at engine speeds at or close to high idle.
  • Ground Speed Control sets the desired top speed by the operator if job site conditions or segment speed limits require a speed less than full run out. Machine Speed Limit is intended for use when top speed needs to be limited for longer durations and Ground Speed Control is intended for use when the top speed needs to be reduced for shorter segments or intermediate periods of time. The operator can set the desired top speed and the machine will find the correct gear that works best for the engine and transmission. In most cases, allowing the engine and transmission to select the correct gear to pull the load will result in a lower engine load factor and lower fuel burn verses top gear selection.
  • Fuel Economy Mode is a two part feature when selected, the first part of the feature lowers the transmission shift points allowing shifting to take place at lower rpms to aid in fuel savings. The second part of the Fuel Economy Mode allows the machine, when operated at engine rpms less than full throttle, to automatically vary the power distribution between the tractor and the scraper, allowing the machine to utilize the more efficient tractor power train vs. the full time torque convertor drive scraper power train.

Standard Equipment

  • Cat C18 engine with MEUI™
  • Compression engine brake
  • Electric start, 24V
  • Air cleaner, dry type with precleaner
  • Fan, hydraulic
  • Ground level engine shutdown
  • Radiator, aluminum unit core, 9 fins per inch
  • Guard, crankcase
  • Starting aid, ether
  • Braking system:
    • Primary and secondary, wet disc, hydraulic actuated
    • Parking, hydraulic-released, spring-applied
  • Throttle lock
  • Transmission:
    • 8-speed planetary power shift
    • ECPC control
    • APECS software
    • Programmable top gear selection
    • Transmission hold
    • Differential lock
    • Guard, power train
    • Standard tire spin reduction
    • Ground speed control
    • Machine speed limit
    • Differential lock protection
  • Cat C9.3 engine
    • High pressure common rail fuel
    • Constant lift engine brake
  • Electric start, 24V
  • Air cleaner, dry type with precleaner
  • Fan, mechanical driven
  • Ground level engine shutdown
  • Radiator, aluminum unit core, 9 fins per inch
  • Starting aid, either
  • Braking system:
    • Primary and secondary, dry caliper, hydraulic actuated
  • Transmission:
    • 4-speed (torque converter drive)
    • Planetary power shift
  • Alternator, 150 Amp
  • Batteries (4), 12V, 1,000 CCA, maintenance free, high output
  • Electrical system, 24V
  • Lighting system:
    • Headlights, LED
    • Turn signals with hazard function, LED floodlights, (2) cutting edge (1) bowl, halogen side vision (2)
  • Starting/charging receptacle
  • Alarm, backup
  • Batteries (4) 12V, 1,000 CAA, maintenance free, high output
  • Alternator, 65 Amp
  • Electrical system, 24V
  • Lighting system:
    • Brake lights, LED
    • Turn signals with hazard function, LED
  • HVAC system, heat, AC, defrost
  • Thermostat control of HVAC system
  • Coat hook
  • Lunchbox platform with holding strap
  • Diagnostic connection (2)
  • 12V power ports (2)
  • Differential lock (1)
  • Dome courtesy light
  • Horn, electric
  • T-handle implement control
  • Mirror, rearview
  • Radio ready
  • ROPS/FOPS cab, pressurized
  • Keypad switches:
    • Throttle lock
    • Wipers/washers
    • Hazard lights
    • Retarding level select
    • Work lights on, off
    • Information mode on Messenger Display
  • Safety tab rocker switches
  • Seat belt, static two-piece
  • Seat, Cat Advanced Ride Management (ARM), Cat Comfort Series 3, rotates 30 degrees
  • Steering wheel, tilt, telescoping, padded
  • Windows, right side emergency egress
  • Windows, sliding
  • Windows, laminated, zipped in
  • Windshield wipers, front and rear windows, includes washers
  • Door lock
  • Messenger Display
  • Gauges, warnings include:
    • Coolant temperature
    • Engine oil temperature
    • Hydraulic oil temperature
    • Fuel level
    • Park brake
    • Implement lockout
    • Brake system
    • Throttle lock
    • System voltage
    • Secondary steering
    • Bail down
    • Ejector auto
    • Differential lock
    • Apron float
    • Transmission hold
    • Cushion hitch
    • High beam lights
    • Action lamp
    • Engine speed, rpm
    • Gear selection
  • Extended Life Coolant to –37° C (–34° F)
  • Advanced cushion hitch
  • Accumulators (cushion hitch) with Canadian Registration Number (CRN)
  • Fast oil change
  • Fenders, non-metallic
  • Heater, engine coolant 120V
  • Rims (2)
  • Tow hooks, front
  • Vandalism locks
  • Heater, engine coolant 120V
  • Steering locks
  • Coal Bowl
    • 31 m3 (41 yd3), struck
    • 38 m3 (50 yd3), heaped
  • Vandalism locks
  • Scraper fenders
  • Fast oil change
  • Rims (2)
  • Hydraulic position sensing cylinders (bowl lift and apron)

Optional Equipment

  • Secondary Steering Arrangement
  • Sequence Assist Arrangement
  • Advanced Tire Spin Reduction
  • Camera arrangement – WAVS
  • Cab beacon
  • Air horn
  • Air horn and beacon
  • Wiring group
  • Film arrangement – U.S. (ANSI)
  • Film arrangement – International (ISO)