C175-16 (50 HZ) | 2500-3100 kVA Diesel Generator

C175 Generator Set

SPECS SUMMARY

Standby Rating	3100(no fan)/3000 kVA
Prime Power Rating	2825(no fan)/2725 kVA
Emissions/Fuel Strategy	Low Fuel, Low Emissions
Voltage	380 to 11000 Volts

Caterpillar is leading the power generation marketplace with Power Solutions engineered to deliver unmatched flexibility, expandability, reliability, and cost-effectiveness.

Specifications

Standby Rating	3100(no fan)/3000 kVA
Prime Power Rating	2825(no fan)/2725 kVA
Emissions/Fuel Strategy	Low Fuel, Low Emissions
Voltage	380 to 11000 Volts
Frequency	50 Hz
Speed	1500 rpm
Duty Cycle	Standby, Mission Critical, Prime, Continuous
Maximum Rating	3100 kVA
Minimum Rating	2500 kVA
Engine Model	C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
Bore	6.89 in (175 mm)
Stroke	8.66 in (220 mm)
Displacement	5166.88 in³ (84.7 l)
Compression Ratio	16.7:1
Aspiration	Turbo Aftercooled
Fuel System	Common Rail
Governor Type	ADEM� A4
Length - Minimum	241.6 in (6137 mm)
Length - Maximum	311 in (7900 mm)
Width - Minimum	83 in (2110 mm)
Width - Maximum	108.5 in (2786 mm)
Height - Minimum	87 in (2211 mm)
Height - Maximum	130.2 in (3307 mm)
Dry Weight - Genset (minimum)	42750 lb (19391 kg)
Dry Weight - Genset (maximum)	50750 lb (23020 kg)

Benefits and Features

Cat Generator Set Package

Cat generator set packages have been fully prototype tested
Accepts 100% block load in one step and meets NFPA 110 loading requirements
Conform to ISO 8528-5 steady state and transient response requirements

Cat Diesel Engine

Reliable, rugged, durable design
Field-proven in thousands of applications worldwide
Four-stroke-cycle diesel engine combines consistent performance and excellent fuel economy with minimum weight

SR5 Alternator

Superior motor starting capability minimizes need for oversizing alternator
Designed to match performance and output characteristics of Cat diesel engines
Robust Class H insulation

Cat ECS Control Panel

User-friendly interface and navigation
Scalable system to meet a wide range of installation requirement
Expansion modules and site-specific programming for specific customer requirements

Cooling System

Designed to operate in standard ambient temperatures up to 50°C (122°F)
Contact your Cat Dealer for specific ambient and altitude capabilities

Certifications

EU Declaration of Incorporation
EU Declaration of Conformity
IBC seismic certification
Eurasian Conformity (EAC)

One Safe Source

Components used in the generator set are selected at the design stage to provide optimum package performance
The generator set is fully assembled at a Caterpillar facility following our quality guidelines
Each generator set package is tested before leaving the Caterpillar facility
Cat product support, including dealer service, parts and warranty covers the entire Cat power system

Worldwide Product Support

Cat dealers have over 1,800 dealer branch stores operating in 200 countries
Your local Cat dealer provides extensive post-sale support, including maintenance and repair agreements

Standard Equipment

Air Inlet System

4 x Single element canister with service indicator(s)

Control Panel

Cat ECS 100
Volts (L-L & L-N)
Engine cycle crank
Power factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable protective relaying functions
High coolant temperature
Accessory module data link
Low coolant level
Over/under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse reactive power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning/shutdown Indicators:
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto/start/stop control.
Low oil pressure
RPM
Text alarm/event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer
Operating hours
Over/under voltage
Overspeed
Frequency (Hz)

Cooling System

Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards

Exhaust System

Bolted flange, with bellow for each turbo
Dry exhaust manifold

Fuel System

Filters x 3
Secondary/ tertiary fuel filters
10 Micron spin On Type
4 Micron Spin On Type
Primary fuel filter water/fuel water separator
Engine mounted filters x 3

Generator and Attachments

6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form wound
Permanent magnet excitation (PMG)
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti-condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry

Governing System

ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)

Lube System

Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube Oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby

Mounting Systems

Rubber anti-vibration mounts - shipped loose
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine/generator

Service Instructions

Two PM inspections

Power Termination

Busbar

General

Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand servicing
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation

Optional Equipment

Air Inlet System

Single element air cleaner
Dual element air cleaner
Air inlet adapters
Air inlet protection

Control Panel

EMCP 4.4
EMCP 4.4 optional harness
Controller and MV&HV power connection locations
Load share module
Controller mounting location - LV / MV
Customer AC-DC connection mounting location - LV/MV
Load share module / auxiliary plate and auxiliary box (LV)
Load share governor
Frame boxes
Automatically selected ground
Controller voltage and current sensing groups
Raise lower switch
Speed adjust
Annunciator modules
Customer interface options
Generator temperature monitoring
Modbus monitoring of packages
E-Stop
Interconnect harness
Generator harness

Cooling System

Package mounted radiator
Remote radiators
Fuel cooler

Exhaust System

Front housing - Standby or mission critical
Front housing - Prime or continuous
Exhaust collectors/manifold
Exhaust support group
Mufflers
Weld flanges
Aftercooler drain

Crankcase Systems

Explosive relief valves
Crankcase ventilation system

Fuel System

Primary fuel filter

Generators and Attachments

Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
Medium voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
Low voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
Space heater kit
Thermostat for space heater
Conversion GP - Top cable entry
Generator air intake
Differential current transformers

Instrumentation

Pyrometer and thermocouples

Lube System

Lube oil heater
Drain group oil pans
Lubricating oil
Electric prelube pumps
Oil filters

Mounting

Rubber anti-vibration mounts
Spring type linear vibration isolators
IBC vibration isolators - Shipped loose

Power Connections

Center post busbarss (LV)
Side/rear mounted busbars (LV)
Harnesses (Breaker)
Cable entry options (LV)
Enclosures - Control packaging (LV)
Power connection covers (LV)
Neutral ground (LV)
1800 Frame generators Circuit breaker
Masterpack breakers
Paralleling circuit breakers
1800 Frame generator side / rear mounted busbars (MV)
Cable entry options (MV)
Neutral ground (MV)
Low voltage connection cable
Masterpack breaker connections

Special Tests / Reports

Generator test report
PGS Test report @ 1.0 power factor
PGS Test report @ 0.8 power factor
Standard genset TVA (Torsional Vibration Analysis) report
Custom generator TVA report
Special test charge - Engine only
Genset fuel consumption test
Standard engine test charge
IBC seismic Certification
OSCOSH1 seismic Certification

Starting / Charging System

General

Special paint colors
Service tools - Engine barring group
Barring group manual
Engine barring air powered
Control GP - air powered bar group