C175-16 (60 HZ) | 2500-3100 kW Diesel Generator

C175 Generator Set

SPECS SUMMARY

Standby Rating	3365(no fan)/3250/3100(no fan)/3000 ekW
Prime Power Rating	3115(no fan)/3000/2825(no fan)/2725 ekW
Emissions/Fuel Strategy	Low Fuel, Tier 2
Voltage	480 to 13800 Volts

Caterpillar is leading the power generation marketplace with Power Solutions engineered to deliver unmatched flexibility, expandability, reliability, and cost-effectiveness.

Specifications

Standby Rating	3365(no fan)/3250/3100(no fan)/3000 ekW
Prime Power Rating	3115(no fan)/3000/2825(no fan)/2725 ekW
Emissions/Fuel Strategy	Low Fuel, Tier 2
Voltage	480 to 13800 Volts
Frequency	60 Hz
Speed	1800 RPM
Duty Cycle	Standby, Mission Critical, Prime, Continuous
Maximum Rating	3365 ekW
Minimum Rating	2500 ekW
Engine Model	C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
Bore	6.89 in (175 mm)
Stroke	8.66 in (220 mm)
Displacement	6456.31 in³ (84.7 l)
Compression Ratio	16.7:1
Aspiration	Turbo Aftercooled
Fuel System	Common Rail
Governor Type	ADEM� A4
Length - Minimum	241.6 in (6137 mm)
Length - Maximum	312.9 in (7947 mm)
Width - Minimum	83.1 in (2110 mm)
Width - Maximum	113.7 in (2889 mm)
Height - Minimum	87 in (2211 mm)
Height - Maximum	134.3 in (3410 mm)
Dry Weight - Genset (minimum)	42750 lb (19391 kg)
Dry Weight - Genset (maximum)	50500 lb (22906 kg)

Benefits and Features

Cat Generator Set Package

Cat generator set packages have been fully prototype tested
Accepts 100% block load in one step and meets NFPA 110 loading requirements
Conform to ISO 8528-5 steady state and transient response requirements

Cat Diesel Engine

Reliable, rugged, durable design
Field-proven in thousands of applications worldwide
Four-stroke-cycle diesel engine combines consistent performance and excellent fuel economy with minimum weight

SR5 Alternator

Superior motor starting capability minimizes need for oversizing alternator
Designed to match performance and output characteristics of Cat diesel engines
Robust Class H insulation

Cat ECS Control Panel

User-friendly interface and navigation
Scalable system to meet a wide range of installation requirement
Expansion modules and site-specific programming for specific customer requirements

Cooling System

Designed to operate in standard ambient temperatures up to 50°C (122°F)
Contact your Cat Dealer for specific ambient and altitude capabilities

Certifications

UL 2200 Listed
CSA
IBC seismic certification
OSHPD pre-approval

One Safe Source

Components used in the generator set are selected at the design stage to provide optimum package performance
The generator set is fully assembled at a Caterpillar facility following our quality guidelines
Each generator set package is tested before leaving the Caterpillar facility
Cat product support, including dealer service, parts and warranty covers the entire Cat power system

Worldwide Product Support

Cat dealers have over 1,800 dealer branch stores operating in 200 countries
Your local Cat dealer provides extensive post-sale support, including maintenance and repair agreements

Standard Equipment

Air Inlet System

4 x Single element canister with service indicator(s).

Control Panel

2 Programmable relay outputs (Form C)
Low coolant level
Over/under voltage
Coolant temperature
Serial annunciator module data link
Alarm acknowledge
Text alarm/event descriptions
Volts (L-L & L-N)
Reverse power
Over/under frequency
Environmental sealed front face
Programmable protective relaying functions
Speed adjust
Generator phase sequence
Low coolant temperature
Generator mounted - rear facing
Overspeed
Controls
Frequency (Hz)
Engine cycle crank
Engine cool-down timer
Warning/shutdown Indicators:
Lamp test
2 Programmable digital outputs
6 Programmable digital inputs
High coolant temperature
Customer data link (Modbus RTU)
Auto/start/stop control
Emergency stop pushbutton
RPM
Digital Indicators
Communications
Accessory module data link
Oil pressure (psi, kPa or bar)
Low oil pressure
Overcurrent
Emergency stop
24 Volt DC operation
4 Programmable relay outputs (Form A)
Failure to start (overcrank)
True RMS AC metering, 3-phase, +/-2% accuracy
Power factor (per phase & average)
Operating hours
DC volts
Amps (per phase & average)
Cat ECS 100
Reverse reactive power

Exhaust System

Bolted flange, with bellow for each turbo
Exhaust flange outlet

Fuel System

Engine mounted filters #REF!
Filters x 3
10 Micron spin on yype
Secondary/tertiary fuel filters
4 Micron spin on type
Primary fuel filter water/fuel water separator

Generators and Attachments

Right side extension box, bottom cable entry
IEC platinum stator RTDs
Reactive droop capability
3 Phase voltage sensing
(MV) Busbar connections, right side extension box, bottom cable entry
Class F temperature rise at 40C ambient
Anti-condensation space heater
NEMA Class H insulation
6 Leads
Class H temperature rise at 40C ambient
Voltage regulator
Exciter diode monitor
Form wound
RFI suppression
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase brushless
60 Hz models: NEMA standard hole pattern
Permanent magnet excitation (PMG)
Min / max exciter limiter
Salient pole

Governing System

Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
ADEM A4

Lube System

Oil filter, filler and dipstick
Integral lube Oil cooler
Oil drain lines and valve
Fumes disposal
Lubricating oil
Prelube - required with prime, continuous, and standby
Gear type lube oil pump

Mounting Systems

Rails - Engine/generator
Rubber anti-vibration mounts - shipped loose
Dual 24 volt electric starting motors
Battery disconnect switch
Batteries and battery rack w/cables

Power Termination

Busbar

Service Instructions

Two PM inspections

General

Paint - Caterpillar yellow with high gloss black rails & radiator
SAE standard rotation
LH Service
Flywheel and flywheel housing-SAE No. 00

Optional Equipment

Air Inlet System

Air inlet adapters
Dual element air cleaner
Single element air cleaner
Air inlet protection

Control Panel

Package mounted radiator
Automatically selected ground
Customer AC-DC connection mounting location - LV/MV
Load share governor
EMCP 4.4
E-Stop
Frame boxes
Annunciator modules
Load share module / auxiliary plate and auxiliary box (LV)
Fuel cooler
Controller mounting location - LV/MV
Modbus monitoring of packages
Customer interface options
EMCP 4.4 optional harness
Controller voltage and current sensing groups
Remote radiators
Generator harness
Interconnect harness
Speed adjust
Controller and MV and HV power connection locations
Raise lower switch

Crankcase Systems

Explosive relief valves
Crankcase ventilation system

Exhaust System

Mufflers
Exhaust support group
Weld flanges
Exhaust collectors/manifold
Front housing - Prime or continuous
Front housing - Standby or mission critical
Aftercooler drain

Fuel System

Primary fuel filter

Generators and Attachments

Low voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
Medium voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
Conversion GP - Top cable entry
Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
Differential current transformers
Space heater kit
Medium voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
Thermostat for space heater
Generator air intake

Instrumentation

Pyrometer and thermocouples

Lube System

Drain group oil pans
Oil filters
Lube oil heater
Electric prelube pumps
Lubricating oil

Mounting Systems

IBC vibration isolators - Shipped loose
Spring type linear vibration isolators
Rubber anti-vibration mounts

Power Connections

Low voltage connection cable
Center post busbarss (LV)
1800 Frame generator side / rear mounted busbars (MV)
Enclosures - Control packaging (LV)
Paralleling circuit breakers
1800 Frame generators Circuit breaker
Neutral ground (LV)
Neutral ground (MV)
Cable entry options (LV)
Cable entry options (MV)
Masterpack breakers
Power connection covers (LV)
Harnesses (Breaker)
Masterpack breaker connections
Side/rear mounted busbars (LV)

Special Tests / Reports

IBC seismic Certification
Special test charge - Engine only
PGS Test report @ 0.8 power factor
Genset fuel consumption test
Standard genset TVA (Torsional Vibration Analysis) report
PGS Test report @ 1.0 power factor
OSCOSH1 seismic Certification
Custom generator TVA report
Generator test report
Standard engine test charge

Starting / Charging System

General

Special paint colors
Control GP - air powered bar group
Barring group manual
Service tools - Engine barring group
Engine barring air powered