Request Info

SPECS SUMMARY

Minimum Rating2320 BHP (1730 bkW)
Maximum Rating7268 BHP (5420 bkW)
AspirationTA
ConfigurationIn-Line 6, Vee 8, Vee 12, Vee 16, 4-Stroke-Cycle Diesel
Cat C280 Marine Auxiliary Engines

Specifications

Minimum Rating2320 BHP (1730 bkW)
Maximum Rating7268 BHP (5420 bkW)
AspirationTA
ConfigurationIn-Line 6, Vee 8, Vee 12, Vee 16, 4-Stroke-Cycle Diesel
Bore11 in (280 mm)
Stroke11.8 in (300 mm)
Maximum Width69 in (1741 mm)
Minimum Height108 in (2733 mm)
Minimum Dry Weight34496 lb (15680 kg)
Maximum Height140 in (3550 mm)
Minimum Width67 in (1704 mm)
Minimum Length145 in (3691 mm)
Maximum Length197 in (5007 mm)
Maximum Dry Weight62832 lb (28500 kg)

Benefits and Features

CAN J1939 data link Waterproof connectors, Maintenance-free, Backup ECU for redundant governing

Load feedback, Programmable droop, Adjustable gain, Adjustable fuel/air ratio control, Histograms of engine operation, Cat Messenger display presents diagnostics and other engine parameters

Engine speed, Boost pressure, Throttle position, Fuel consumption rate, Inlet manifold temperature, Diagnostic codes and events, Configuration, Desired engine speed, Battery voltage, Engine load, Lifetime totals — engine hours, fuel burned, idle fuel, idle hours, Trip totals — average fuel rate, idle fuel, idle hours, engine hours, fuel burned, trip reset

Interfaces with standard Cat® Marine Monitoring System (PLC in Price List) Provides visual indication of ECU functionality, Accepts 4 — 20 mA or PWM remote throttle speed input, Marine alarm and protection

“Drop-in” installation, No threaded fuel connections, High pressure inside injector only, Does not require double wall fuel lines or leak collection device, Injector synchronization not required

Standard Equipment

  • R INLET SYSTEM Aftercooler, fresh water, corrosion resistant coated (air side) Air inlet shutoff Breather, crankcase, top-mounted Turbocharger, rear-mounted, engine oil lubricated
  • Single Caterpillar A-III Electronic Engine Control Modules with Electronic Unit Injector Fuel System Rigid Wiring Harness (10 amp 24volt power required to drive Electronic Engine Control Modules)
  • Engine coolant water drains
  • Dry, gas tight, exhaust manifold
  • Distillate fuel (requires viscosity ranging from 1.4 cSt to 20 cSt at 38 degrees C) Fuel transfer pump (mounted on left hand side) Duplex fuel filters Electronically Controlled Unit Injectors
  • Centrifugal oil filters with single shutoff. Service side engine mounted on cylinder block inspection covers. Includes installed oil lines and single shutoff valve. Filters centrifuge bypass oil from the main lubricating oil pump. Can be serviced with the engine running. Oil filler and dipstick Valve, oil pressure regulating Valves, crankcase explosion relief
  • Paint, Caterpillar yellow Pumps, gear driven: fuel, oil, jacket water, aftercooler/oil cooler water
  • Service literature. Included standard with each engine are two (2) complete sets of service literature listed below: 1. Custom parts book CD (serial number specific) 2. Service manual, which includes: Operation & Maintenance, Specifications, Systems Operation, Testing and Adjusting, Disassembly and Assembly manual. Available in paper media and English language only. 3. Technical manual (parts/service information for special equipment). Available in paper media in English language only. NOTE: Custom parts book CD and service manual can be re-ordered through the normal Caterpillar literature ordering system. The technical manual can only be re-ordered through the Project Services at the Caterpillar Lafayette Engine Center facility.

Optional Equipment

  • Air Cleaners
  • Jacket Water Heaters
  • Heat Recovery System
  • Heat Recovery Thermostats
  • Cooling System Connection Groups
  • De-Aerator
  • Load Sharing module
  • Direct Rack Module
  • Outlet Expander
  • Flexible Exhaust Fittings
  • Weld Flange - Optional
  • Fuel Priming Pump
  • Duplex Primary Fuel Strainer
  • Fuel System Connections
  • Oil Pan Drain Valve
  • Prelubrication Connections
  • Lube Oil Heater
  • Vibration Isolators
  • PLC Monitoring System Options
  • ECP Relay System Options
  • ECP Mechanical Gauge Instrument Panel
  • Turbocharger Speed Sensor
  • Cylinder Pressure Relief Valve
  • Oil Mist Detector
  • Protection System Components
  • Magnetic Pickup
  • Intake and Air System
  • Basic Engine
  • Cylinder Head
  • Fuel System
  • Cooling System
  • Instrumentation
  • Cylinder Valve Kits
  • Basic System Testing
  • Special Witness Test
  • Torsional Vibration Analysis
  • Commissioning
  • Service Tools
  • Factory Packaging
  • Shipping Protection-Shrink Wrap or Tarp
  • Shipping Protection-Export Boxing
  • AID Emblem
  • Storage Preservation