For any petroleum application, trust Caterpillar to meet your project needs with custom factory generator sets and mechanical packages. Cat engines, generators, controls, radiators, and transmissions can be custom designed and matched in collaboration with our local dealers to create unique solutions. Custom packages are globally supported and are covered by a one year warranty after startup.

Caterpillar has a full line of engine-transmission packages that can be fully integrated with your axle, hydraulics, and operator interface. Cat transmissions deliver continuous operation under full load, smooth shifting at any speed, and maximum up time, with unmatched durability and easy maintenance.

Large variety of factory-installed engine attachments reduces packaging time

Every engine is full-load tested to ensure proper engine performance.

- More than 2,200 dealer outlets - Cat factory-trained dealer technicians service every aspect of your petroleum engine - Cat parts and labor warranty - Preventive maintenance agreements available for repairbefore-failure options - S•O•SSM program matches your oil and coolant samples against Caterpillar set standards

Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.

Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.

For all your petroleum power requirements, visit www.catoilandgasinfo.com.

For all your petroleum power requirements, visit www.catoilandgasinfo.com.

• Electronic governing, PTO speed control
• Programmable ratings
• Cold mode start strategy
• Automatic altitude compensation
• Power compensation for fuel temperature
• Programmable low and high idle and TEL
• Electronic diagnostics and fault logging
• Engine monitoring and protection system (speed, temperature, pressure)
• J1939 Broadcast (diagnostic, engine status, and control)

• Thermostats and housing — outlet vertical
• Jacket water pump — gear-driven, centrifugal, RH
• RH front water pump inlet
• All plugs/fittings are STOR for lines gp water

• Exhaust manifold — dry
• Front turbo exhaust
• Full marmon connection, maximum load 10 kg for direct connection to turbo

• See Mandatory Options

• MEUI system
• Fuel filter, secondary, mid-mount (LH 2 micron high performance)
• Fuel transfer pump, LH front
• Fuel priming pump, LH mid-mount
• Fuel sample valve, mounted on fuel filter base

• Crankcase breather — rear valve cover
• Oil cooler — RH
• Oil filter — RH
• Oil pan — front sump
• Oil filler — LH front
• Oil dipstick — LH front
• Oil pump
• Oil valve sampling — on oil filter base

• Front support (shipping only)

• Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
• Hydraulic pump drive, SAE A, 11 tooth

• Vibration damper
• Paint — Cat yellow
• Lifting eyes
• Automatic variable timing, electronic
• Electronic installation kit 70-pin connector (connectors, pins, sockets)
• Literature group owner and operator

• Throttle position sensor
• Exhaust system — front or rear
• Flywheel housing or rear PTO
• Primary filter/water separator

• Air chambers
• Air compressor governor

• Air cleaners
• Precleaners
• Air lines
• Air inlet gasket

• Charging alternators
• Alternator mountings
• Alternator wiring
• Circuit breaker mountings
• Alternator belt guard

• Radiator — installed
• Radiator — ship loose
• Fan drive f/u/w Caterpillar installed radiator
• Fan drives for customer-supplied radiators
• Fan height instructions
• Vee belts for customer-supplied radiators
• Aftercooler lines f/u/w Caterpillar installed radiator
• Rear-facing exhaust
• Aftercooler lines
• Suction fan adapters — attaches fan to fan pulley
• Blower fan adapter — attaches fan to fan pulley
• Blower fan
• Suction fan
• Fan belt tightener
• Coolant level sensor
• Dry charge coolant conditioners
• Dry charge coolant conditioner element

• Turbo exhaust connection
• Flexible fitting
• Elbows
• Flanges
• Dry elbow